Team Losi XX-T forum [Archive] - Radio Control Zone

Paul E. Garcia

04-02-2002, 12:44 AM

R Pritchard and Guggi,

I believe the dual-disk slipper ought to work, in fact I believe Losi has a retrofit kit for the XX series. The dual disk slipper is simple; it essentially replaces the hydra-drive and keyed spur gear with a spur gear slotted for slipper pads on both sides, and a slipper pad and plate similar to the ones already on the truck. I would think you could put one together without the actual kit.

I'm not sure of the benefits of the Hydra-Drive vs the single slipper setup or the dual slipper conversion; I run the Hydra simply because I lost the parts for the straight slipper setup.

rpritchard

04-02-2002, 12:47 AM

FYI, www.hotrodhobbies.com has the slipper parts. I just bought the slipper kit last week for like $3.

They don't have an online store, but if you call them they might be able to get the parts to you. They have a ton of XX series parts and hop-ups

hardcoretmaxx

04-12-2002, 11:58 PM

I have a xxt and I like it I can get it to wheelie like no other but the darn idler gear keeps striping I bet you that I have gone through at least 30 I have had it for three years and it is the best birthday present I got since but I will be getting a 1/8 buggy for my birthday this year but this truck is a tank if you don't strip idler gears but I have a aluminum diff and the idler gear is the only plastic gear in there but it is easy to fix after a will.

guss

04-21-2002, 09:09 AM

what bodies besides the losi ones fit the xx-t truck ?

losifreak2004

04-22-2002, 05:59 PM

hardcoreTmaxx - If you get rid of the metal diff gear your idler gears will last much longer.

The dual disk slipper is a direct add-on, and is much more consistent than the Hydra-Drive, and easier to get parts for.

I won A LOT of races with my XXT and XXTCR. In fact, I was one of the top 10 Expert Stock drivers in Region 12 with it for quite a while. I still have quite a bit of info on these trucks. If you have any questions, let me know!

Aaron

guggi101

04-22-2002, 06:26 PM

Ya I have a question hw do I sell it? lol ok I love the truck its a wicked truck my best eletric but I am going nitro how do I sell it whats it worth with a novak dually esc p2k2 pro motor python remote cvd's graphite front end, 4 sets of tires titanium turnbuckles, springs in like 6 different rates, hydra drive parts, slipper clutch on it, 2 motor plates, front end pars tons of steering parts, lots of shock fluids and hydra drive fluid. tons of parts and stuff whats it worth? has a body and looks good anyone want it?

losifreak2004

04-23-2002, 12:22 AM

I know its not what you wanna hear, but if you got more than $100 for it, you'd be VERY lucky. Much emphasis on VERY.

And your best bet of that would be eBay.

guggi101

04-23-2002, 06:26 PM

Well I know I can get more then 100 I've been offered 225 and told by chris marcy owner of r/c madness to hold off a week or so cause he knows i can get at least 300. But whatever thats your opinion

losifreak2004

04-24-2002, 06:29 PM

$300.00?

Maybe over eBay, and maybe in your area. But NO WAY will you get over $100 for it anywhere I've been to.

I struggled to sell a brand new XXT-CR Graphite Plus Kit with various aluminum goodies for $150.00 with plenty of other parts. Motors, radios, tires, parts, none of that stuff has any resale value. If you sell what you have for over $200.00, the buyer must have little to no experience. Especially if it's been used.

Aaron

popee

07-09-2002, 12:31 PM

Im Sticking with the XXT,. I live in the UK so its not that Obsolete, as a XXXTMF cost 441USD!!!!!! Im Still Winning races with it, I have a XXX, and I dont find the performance much different than my XXCR-KW, the XXX Understeeers :(
Check out my XXT Still looks mint.

http://www.j00.pwp.blueyonder.co.uk/truck1.JPG

losifreak2004

07-11-2002, 02:27 AM

LOL! Good show with the XXT!

A properly setup XXX series car WILL outrun a XX series car anytime, however.

popee

07-11-2002, 08:59 AM

Running at club level, its great for me, some guys run 'mardave cobras and tamiyas if you ahve heard of mardaves. You get a lot of the Mr4's , shcumhers all of the top range cars, but at my level I dont think id see much of a difference, the Truck is full graphite and its needed on a indoor track where the sides are made up oflage planks of wood.

losifreak2004

07-11-2002, 04:25 PM

Never heard of a Mardave....LOL

Aaron

popee

07-11-2002, 07:48 PM

They was one of the first international RC Manufactures. Started way way back. they do budget cars, you can get a new 1/12th for $30 they go very well too www.mardaveracing.com

evader32

07-12-2002, 12:29 AM

hey do you guys no if any xxt parts are identical to the evader because the evader doesn't have near the amount of upgrade able parts as the xxt and I know for a fact the the front shock towers are the same if you have any info i would like to here it thanks

Gutter Ball

07-12-2002, 12:46 AM

The only Evader at our track uses XXT front/rear graphite arms. He broke his and while they were being sent back, he tried XXT arms. They seem to be a perfect fit.

losifreak2004

07-12-2002, 04:45 AM

evader - Nearly everything is a direct replacement...

Aaron

popee

07-12-2002, 06:25 AM

what the hell is an evader?

losifreak2004

07-12-2002, 06:04 PM

The Duratrax Evader...it's a near-clone of the XXT.

Aaron Waldron

evader32

07-15-2002, 10:47 AM

thanks guys I was thinking of the arms so now that i know they work ill order some

jep_rc

07-15-2002, 10:27 PM

Originally posted by Brndonp17
red Ok guys lets talk about the best off road tuck in the world the Team Losi XXT CR.And post pics of ur trucks to :D

OK, I'm a little late gettng in here, but I just picked up a XXT-CR graphite plus used and it rocks. Beats the pants off the T3's at our track. Here is a pic of the truck during table-top launch...
http://sio.midco.net/jbriden/photos/houston.jpg

See Ya - Jep

losifreak2004

07-16-2002, 02:05 AM

That's some awesome air!

Is it in the middle of a corn field? HAHA

Aaron

jep_rc

07-17-2002, 08:49 AM

Originally posted by losifreak2004
That's some awesome air!

Is it in the middle of a corn field? HAHA

Aaron

Yup - It is our Field of Dreams, "Build it and they will come..." It is surrounded on three sides by corn. The company I work for owns the land and let us use a bit for the track. They lease the rest to a farmer. We built it this year - still need to fine tune the track, but beats the heck out of street bashing.

Jep

losifreak2004

07-25-2002, 02:20 AM

That's awesome!

Aaron Waldron

RallyRoach

07-30-2002, 01:49 PM

Can anyone explain the differences between all the different versions? I'm finding out that I have a bit of a mongrel XXT, with bits from XXT CR and Graphite+ parts mixed in. I know I don't have Hydradrive, which I'm glad for (my brother's is hard to tune), but any other info on the differences would be appreciated.

RallyRoach

losifreak2004

07-30-2002, 02:45 PM

There was only one version of the XXT. The CR had shorter arms, a wider pivot block (which was now a seperate piece from the pivot plate) and different hubs. The Graphite Plus was the CR with all the hop-up parts, plus the dual-disk slipper instead of the Hydra-Drive.

Aaron Waldron

jep_rc

07-30-2002, 10:16 PM

I think Aaron covered most of it - also, I think the CR and Graphite Plus have a longer chassis?

Jep

losifreak2004

07-31-2002, 02:21 AM

That's right! When the XXTCR debuted, Losi came out with the XL chassis, which was 1/4" longer than the L(ong) chassis, which is what came with the XXT.

Aaron Waldron

RallyRoach

07-31-2002, 08:51 AM

Excellent, now things are a bit clearer... I need to replace the chassis and front pivot block soon (most of the screws are stripped out). Would I be better off looking for the 2 piece pivot assembly from a CR or go with the original 1 piece?

Also, what kind of alignment works well for a sandy, short track. Right now I'm just using the "general" set up from Losi's site, with Losi Reptiles (silver) in back and Proline ribbed in front.

Finally, would it be worth it to convert to the dual slipper? What are the benefits?

Thanks

losifreak2004

07-31-2002, 12:40 PM

On a sandy track, you wouldn't feel the difference with a dual slipper.

Both the XXT and CR came with the hinged front end. The CR's rear pivot block and pivot plate were seperate.

Aaron Waldron

Insane Rival

08-01-2002, 09:45 AM

hey everyone! im gonna be a member of this club in about 2 weeks, tradin my GT for a xxt. is this a good strong truck? its gonna have a 15t motor (monsters of speed), LRP IPC sport esc, traxxas tq2 radio and receiver, and some servo. anyways, i hope i enjoy my truck!

losifreak2004

08-01-2002, 01:44 PM

There's no doubt you'll have fun!

Some parts to be worried about: the chassis and front bulkhead where the hinges are, the top plate, and rear pivot block. Other than that, the truck is pretty strong!

Aaron Waldron

Insane Rival

08-01-2002, 03:38 PM

http://pic1.picturetrail.com/VOL125/638663/1023337/11899881.ptp

this is my xxt, well its gonne be, and it has a custom metal front bulkhead, if u look, if u want to see the rest of the pics... go here...

http://www.picturetrail.com/gallery/view?p=999&gid=1023337&uid=638663

losifreak2004

08-01-2002, 10:20 PM

Other companies made metal front bulkheads. The only problem with that becomes the hinges on the chassis. The bulkhead is easier to replace (and less $$$) than a new chassis!

Aaron Waldron

RallyRoach

08-01-2002, 10:25 PM

I had it explained to me that the front bulkhead is like a chassis "fuse". If you hit something badly, chances are the bulkhead will break before anything else...

losifreak2004

08-02-2002, 01:30 AM

Even with the stock bulkhead, the chassis and other front suspension parts can and will still break, but you have a better chance of the bulkhead being the old thing damaged if you leave it stock.

Aaron Waldron

FlyinRazorback

08-02-2002, 06:57 AM

I sold a guy a XX- T CR that I had never driven and he is having problems with it. I am going to paste his problem on here and hopefully one of you guys can help him out. Thanks in advance.

"ive been having a really difficult time with the transmission,
its been slipping really bad as in, when ever the car is at neutral, and i throttle the motor at full, it slipps and moves slow for like 2 seconds then gradually gets a grip and moves and its very hard to take sharp corners cuase the acceleration is very slow due to the slipping. I went to my LHS and i bought brand new slipper pads and tightened the diff and there is still no effect. i tried using the different slipper spring but has no effect at all..whats for effeicient the hydra drive or the simple slipper drive...or better yet...can i make it not slip at all?"

Thanks
Mike

jep_rc

08-02-2002, 08:55 AM

FlyinRazorback -

I have never personally had the hydra-drive (I use the dual slipper), but it sounds like he is using the hydra slipper and doesn't have any fluid in it. Tell him to re-build the hydra slipper (and use the Losi thick hydra fluid), or try the dual slipper conversion kit.

Jep

RallyRoach

08-05-2002, 11:01 PM

I'm going to rebuild the diff this week, any suggestions for what to use for diff grease on my XXT?

jep_rc

08-05-2002, 11:48 PM

I use the Associated silicone diff grease - works great for me.
Jep

RallyRoach

08-06-2002, 07:42 AM

Thanks :) I can actually get that kind here at my lhs, bonus :)

losifreak2004

08-06-2002, 10:49 PM

I never use anything other than Losi diff lube..there's no reason to use anything else!

Aaron Waldron

RallyRoach

08-06-2002, 11:12 PM

Well, a good reason would be that my lhs doesn't have much in the way of Losi stuff, mostly Associated. I'm running Associated shock oil (NOOOO!!!), no probs. I wish I could get the proper Losi stuff, but I really hate mail order... :(

losifreak2004

08-06-2002, 11:41 PM

Well..that would be a reason now wouldn't it!

Aaron

RallyRoach

08-07-2002, 12:58 PM

I'm curious, will the threaded shocks from a Duratrax Evader fit the XXT? I'd like some threaded shocks, and these are cheaper than the Losi ones...

losifreak2004

08-09-2002, 11:23 AM

I don't see why they wouldn't fit.

Aaron Waldron

jep_rc

08-11-2002, 09:57 PM

Re: Evader Shocks - Yes they fit fine. I have a set of Evader shocks set up for weekend asphalt races, and I keep my stock losi's set up for off-road. I have an XXT-CR. The Evader shocks work great.

Jep

RallyRoach

09-26-2002, 08:47 AM

Well, I finally blew the trans to bits this weekend, funny that it was my first time in the A main, and the truck sounded like a rock tumbler on wheels.

Got it apart and discovered a stripped idler and diff gears, the diff thrust bearing exploded, and all the bearings in the trans were crunchy. 4 hours of brake cleaner and Q-tips, I got everything clean. I even tore the seals off the bearings, cleaned and relubed them (note: snap rings fly very far...).

Anyway, before I get it back together, I was wondering what I should be using for lube in the trans. The instuctions for the truck don't say anything about putting lube anywhere in the trans except for the diff. Is there anything I can put on the gears to smooth things up, or should I just leave it alone as suggested?

T.I.A.

RallyRoach

jep_rc

09-26-2002, 03:54 PM

Hi Rally Roach,

I like to put a piece of electrical tape across the tranny seam after rebuilding to keep the dirt out a bit longer, some actually seal it with RTV, but seem over-kill to me.

As far as lube goes, there are different opinions, some run totally dry. I put a *very* small amount of Trinity royal oil on each bearing after cleaning. I put exactly two drops of Losi thick hydra-drive fluid on the idler gear teeth and spin the tranny to spread it around - the hydra fluid is very thick and sticky and coats the gears nicely. Off course you would use the proper silicon diff lube inside the diff if rebuilding, and I like to use Associated black grease on the diff thrust balls/washers.

Jep

CorB

09-26-2002, 05:57 PM

Is it still possible to find parts for a RC10T? :confused:

reddman

09-27-2002, 12:04 AM

i just got ym xxt and the motor revs but the tires and gears don't spin any ideas?

jep_rc

09-28-2002, 12:27 AM

Hey redman,

Could be a lot of things - is the slipper tight? If you use the hydra drive slipper, is it filled with fluid? Is there a pinion gear on the motor shaft, is the set screw tight, and is it engaged with the spur?

Could also be broken teeth on any of the gears outside or inside the tranny, or a stripped Diff gear.

Hey XX-T and XXTCR Owners - I just posted a bunch of XX-T Parts on eBay, you can link to my auctions from my webpage (in my signature)

Jep
Jep-R/C Products (http://www.geocities.com/jep_rc/)

tonylukes

10-03-2002, 02:40 PM

not really familiar with Losi XX and XXT's (just got one off ebay though). Can you mount a XXT body on the XX? also what are the major differences between a XX and XXT? better shocks and suspension? Thanks.

dave

jep_rc

10-06-2002, 12:37 AM

Hey tonylukes (or is it Dave?),

The XX is an off-road buggy, and the XX-T is an off-road truck. Not realy the same thing - like comparing apples to oranges.

Jep

reddman

10-06-2002, 01:19 AM

yea kinda like a XXX and XXXT any way no it wont fit

RallyRoach

10-06-2002, 09:43 PM

Okay, I just rebuilt my trans last week. I put 6 packs through it in the last week or so, and now, my idler is clicking again..., I haven't taken it apart to verify, but I bet that's what it is... Anyone got any suggestions to improve longevity on this part? I've only got 3 idlers left....

Thanks...

BobT

10-09-2002, 11:33 AM

Originally posted by RallyRoach
Anyway, before I get it back together, I was wondering what I should be using for lube in the trans. The instuctions for the truck don't say anything about putting lube anywhere in the trans except for the diff. Is there anything I can put on the gears to smooth things up, or should I just leave it alone as suggested?

T.I.A.

RallyRoach

Losi Hydra-Drive Fluid! My hydradrive went the way of the dinosaurs but I still use the fluid.

One small drop on each of the three tranny gears will lube them just right until they wear-in a little. Then no lube is nessasary.

My first truck: Losi XXT with the CR conversion. It still had the short truck chassis which gave it too much steering. My next truck (XXT Graphite +) was much easier to drive.

jep_rc

10-26-2002, 10:17 AM

Re: tranny: Ditto what BobT said -

After a thorough rebuild/cleaning, I put a drop of Trinity Royal oil (any good bearing oil will do) on each bearing and let it soak in, then wipe off excess with q-tip. I put barely a drop of thick hydra fluid on the idler and turn everything to spread it around - it really keeps the tranny smooth and quiet.

BobT - I own a XXT-CR Graphite plus as well. It is my first "real" racing truck, and I love it (DTX Evader was my first truck - my 8yr old inherited it). I ditched the hydra as well, and run the dual slipper.

Jep

RallyRoach

10-26-2002, 04:15 PM

Thanks for the replies guys. I tried some regular weight hydra oil, and the truck ran fine all weekend (except for a broken rear pivot plate, which I fixed by using zip ties :). Too bad I'll have to wait until next year to race it again, :(

Anyway, I just wanted to note that Proline Sand Paws work really well on a sandy track. Our tack is nothing but sand, and its fine for the first 2 hours, but then it dries out too much and traction is scarce. I use Proline Gladiators (as do most of the other racers there), but I had a set of paddle tires that came with the truck when I bought it. I actually made the A-main, but I realy had no chance of winning, so I thought I'd have some fun and put the paddles on. Wow! Sand flying everywhere and traction! Plus, with a little practice, I could turn just as well as the others.

Basically, I'd slow for the corner early, then floor it, dig in, and fly ahead. Pulled off 2nd place (running 2000 packs, a Trinity SpeedGems 2 17D) against some much faster machinery, but noone had grip but me :)

Anyway, sorry for so long a post, but I just wanted to say that a basic XXT is still a good race truck :)

RallyRoach

stumpy497

10-28-2002, 08:36 PM

I have an older XXT truck that I would like to get rid of, but I have been away from RCing for so long that I don't know what it is worth. It is loaded with lots of goodies, and tons of spare parts, but I can't remember all of them off the top of my head, and I don't have the truck to look at right now. Do you have any idea of it's worth? Let me know at stumpy497@hotmail.com.

Thanks.

P.S. Anyone one interested in the truck?

jep_rc

10-29-2002, 01:42 PM

Stumpy -

It is really hard to estimate the value without knowing *exactly* what you are including with the truck - rolling chassis only?, motor?, ESC, other elecs?, etc. Also need to know all the hop-ups. XXT trucks sell every week on eBay - go there and use the advanced search to look at completed auctions and see what they are going for. Or look thru Buy/Sell/Trade forum here.

As a point of reference, I picked up a well used XXT-"CR" Graphite Plus rolling chassis with all the goodies (graphite parts, MIP CVDs, Lundford turnbuckles, etc.) and a handfull of replacement parts, all for $60.00 on eBay about a month ago.

I might be interested in your truck, but you will have to take the time to describe it in exact detail. Oh yeah, and only post it for sale in the Buy/Sell/Trade forums, then drop a note here.

Jep

jep_rc

11-10-2002, 08:21 AM

Hi Everyone,

Just finished putting a new lid on my XX-T 'CR' Graphite Plus. Thought I would post them to keep this thread going. Let me know what you think.

http://sio.midco.net/jbriden/photos/lid1.jpg
http://sio.midco.net/jbriden/photos/lid2.jpg
http://sio.midco.net/jbriden/photos/lid3.jpg
http://sio.midco.net/jbriden/photos/lid4.jpg

Jep

trxstr1961

11-26-2002, 02:33 PM

nice job jep, im getting a XXT soon too. will be hanging out here alot after i get it;)

grewst

11-29-2002, 04:37 PM

This is kinda a silly question,,,, but,,, does one know the diameter of the diff screw,,, (is it 3 m )??

jep_rc

12-09-2002, 09:22 AM

Originally posted by grewst
This is kinda a silly question,,,, but,,, does one know the diameter of the diff screw,,, (is it 3 m )??
grewst -
The diff screw on the XX-T series trucks is an SAE 4-40.

Jep

grewst

12-09-2002, 02:38 PM

thanks jep

xxter

12-18-2002, 08:51 PM

My xxt cr graphite plus with a 14turn speed gems motor and Duratrax Streak ESC. The Hpi super nitro rally in the pic was also mine which I've sold. The xxt is the BEST rc vehicle I've ever had!

Tenover

12-18-2002, 10:44 PM

I just aqquired a killer XXt-cr in a trade, and it has the yellow wheels. Can I buy different colored ones for it?

jep_rc

12-19-2002, 08:57 AM

xxter -

You can buy the XXT wheels with the clear lexan disks and paint (the back side) of the clear disks any color you want. The plastic part of the wheels is either yellow, white or natural. You can dye the white ones any color you want.

The XXT wheels are getting hard to find, but you can use the new XXXT wheels - they are solid colors and do not use the clear disks. They come in many colors, but you can dye the white ones as well.

Check out Losi, RPM, and Pro-line. Any of their wheels for the XXT or XXXT should fit.

Jep

xxter

12-20-2002, 05:39 PM

Hello, I am wanting to get a new look for my xxt cr truck by getting a new body. I am a huge fan of dodge trucks. I did some searching and really the only dodge truck body I've seen closest to fitting a xxt cr on the market is the one from Hot Bodies called Ram-It. I posted the pic of it along with my post. Notice the Mopar scheme? Anyone know if these decals come with it and if not where to get them? Also, I notice that it says that this body was designed to fit the Losi LXT but it states that it may be modified to fit similar trucks. Will the mount on the xxt cr without ripping the body all apart? If anyone knows of any other Dodge bodies on the market for our trucks, please tell me who makes it. Thanks, Gary

Collari-Tc3

12-20-2002, 11:10 PM

Hey guys, this is my first post here. I'm glad people are still using the good old xxt. It is an awsome truck and my first real rc. I recently put a brushless in mine, and it cooks. Does anyone know if they still make a rpm heavy duty plastic gear cover? The stock ones are weak.
jep, that is a sharp looking xxt.

jep_rc

12-23-2002, 10:46 AM

xxter -

Any of the bodies designed for the XXX-T also fit the XX-T pretty well. There should be a bunch to choose from. Check out Losi at Horizon Hobbies, also Pro-line, Hot Bodies, Andy's R/C Bodies, Mcallister Racing Bodies, to name a few.

Most (not all) only come with window masks, grill, lights and a few logos. For detail decals, check out Autographics of California, they have every type of decal set you can imagine. Also Parma, and a few others.

Here is a link to Mcallister's Dodge body....

Dodge Body (http://www.flagstaff.az.us/mcallister/page24.html)

Jep

drumr racer

01-01-2003, 03:43 PM

I have a XXtcr, and whoever could spend their time to help me figure out how to do this, I would really appreciate this.
:D

right now, it's christmas time (where the snow comes) actually the first day of '03. So i'm just trying to clean my car and everything for the racing season (for me). There is no snow where I race (Scottsdale RC speedway), but I live many miles away from it (183).

I don't know how to get to my differential from the outside, I wanna clean it and everything, but I can't get to it.

I bought the car used, so i didn't get the thrill of building it. And i didn't get the instruction manual either (to know how to build it).

So could someone E-mail me how to take the "housing" apart (I think). Or E-mail me how to clean it, or what to buy to clean it, or do ALL OF THAT. I'd really appreciate it. :) :cool: :) :D

my e-mail is smouthfan@hotmail.com (www.smouthfan@hotmail.com)
Thanks a bundle.;)

BobT

01-02-2003, 03:20 PM

drumr,

You will need the pdf file located here.
http://www.teamlosi.com/pdfs/exploded/xxtcr.pdf
It will show you how things go together. It will also give you all your part numbers.

There is only one way to work on the diff. You have to remove the tranny and open it up.

Good luck racing.

drumr racer

01-07-2003, 12:21 AM

Thanks a bunch bob T
I guess i should actually get that graphite Trans. case
I just got a new servo for my car, and installled it. dang does that thing have torque, I wedged myself on a tree in pheonix while i was testing the servo, and turned the wheels towards the tree, and got unstuck. Boy did I have a fun time at the track. I got there at eleven, then stayed there untill eleven
I tried selling my old servo to some people, even the shop, 4 two dollars, they wouldn't buy it! :p

BobT

01-07-2003, 01:04 PM

A graphite tranny case will not make your truck any faster. Buy the standard case and save your money for another battery pack. ;)

kam

01-08-2003, 04:16 PM

HELP!!
My son busted the Front chassis stiffener on his xxt.
Part# is A-4110
Everywhere I've checked is backordered(are they even making them still?)
Does anyone know if there is an interchangeable equivelant from another car??

drumr racer

01-08-2003, 10:28 PM

Kam... You're my hero, i thought that there was someone else out ther like that, and I was right I'm soo exited to help you
I've broken through that part twenty eight ( yes count them 28) times. That's the only thing that I think is wrong with the car ( Team Losi is good),;)
They still make it because it goes on other cars too like all of the XX series. Just wait for the piece to come to your local hobbie store.
There is always Graphite, It's part # 9900 it goes for 11.00
Graphite breaks too, but there is a slight chance that it won't break, if he hits something in the front, it usually breaks.
If it breaks like three times, try getting a new front bulkhead. I don't know what part number it is, just when you go into the shop ask them for a Team Losi front bulkhead, they ask what type of car it is, just say it's a XXt. Then ask him how to install it onto the chassis.

BTW the part he broke was a Chassis brace.

BobT

01-09-2003, 12:27 PM

Originally posted by kam
HELP!!
My son busted the Front chassis stiffener on his xxt.
Part# is A-4110
Everywhere I've checked is backordered(are they even making them still?)
Does anyone know if there is an interchangeable equivelant from another car??

kam,

Yes they should still be available. Make sure the front bulkhead is ok. The hing areas take a lot of stress and will break a loop or two. They will look fine but the whole front end will be loose. As long as you are replacing the chassis brace you might as well replace the bulkhead.

P.S. The white bulkhead is stronger than the original one and should hold up better.

kam

01-10-2003, 05:15 AM

Thanks a bunch guys!
I fabricated a temporary replacement for him until I can get the brace and bulkhead.

kam

01-10-2003, 04:04 PM

Another quick question....I finally found a place online that has the chassis brace.
I dont want to just place a small order, so I'm also getting an extra one along with the bulkhead as suggested.

My question is what else is very common to break?? That way I can have the spares ready.

drumr racer

01-10-2003, 09:34 PM

That same part is common to break
get like 4 of those in 3 graphite (9900), and one plastic (4110)

BobT

01-11-2003, 11:44 AM

Originally posted by kam

My question is what else is very common to break?? That way I can have the spares ready.

The rear hub carriers broke most often on me. That is until I learned a trick to make them stronger.

The horn where the camber link connects to the hub carrier was the weak point. To make it stronger use a longer ball end and put a locknut on the end of it sandwiching the horn. This adds a lot of durability to this part.

Front hub carriers can also be a weak point so add those as well.

drumr racer

01-12-2003, 10:45 PM

You guys (and girls) know a thing about the Team Losi XXtcr, how about helping me out by giving me a hand.

I wanna keep this car a long time, so I want as many hop-ups as i could get. I'm talking aluminum, anodized, graphite, anything that is better than stock, or to make it look better.

can you state a website for me to go to, or offer me something that will help in durability, and performance wise

I just wanna know what's out there
thanks:)

kam

01-13-2003, 04:33 PM

Originally posted by drumr racer
You guys (and girls) know a thing about the Team Losi XXtcr, how about helping me out by giving me a hand.

I wanna keep this car a long time, so I want as many hop-ups as i could get. I'm talking aluminum, anodized, graphite, anything that is better than stock, or to make it look better.

can you state a website for me to go to, or offer me something that will help in durability, and performance wise

I just wanna know what's out there
thanks:)

This is something I want to find out too!
I've been going back and forth thinking about just moving my son on to a XXXT.

drumr racer

01-13-2003, 10:34 PM

Hey Kam,
If your son wants to race, get him something that is kinda new, that has alot of replacement parts for it, I'm not saying that the XXtcr doesn't have any parts for it, I'm talking about hop-up parts For Performance not really looks (even though the looks are a +)
To race get him a Mat-Francis XXX-T, or if your son likes a challenge, get him a Kinwald Edition XXX buggy.
The thing with the EDITION part is that the car is that you get a rolling chassis, and has all of the hop-ups like Graphite everything that would be plastic on the original version, Titanium Turnbuckles, Thredid shocks (I think) and some aluminum parts minus just about a hundred dollars in aluminum parts for hop-ups. that's about four parts that you can make the car better (that's not electronics). That's a smoking deal

Add about 50$ max to the original price of the regular car, and you get the EDITION.

The Edition type cars don't come with any electronics, but you can buy tham at your lhs. Get a good transmitter that isn't that expensive, but isn't a cheap piece of junk.
Get a XR2 transmitter with a reciever in the same package, and That will be Good. Don't get a package with servos, or with an ESC because you need a good, racing quality ESC, and a Racing quality servo. Don't spend less than $50 give or take a few on a servo.
Get a good quality ESC like a Novak Cyclone2
Because reverse is illegal in races, there are some ESC's that you can push a button to cancel out reverse, and have brake instead.

If your son just wan'ts to backyard bash, get him some essentials for durability for his car, like Titanium Turnbuckles, and new ballcups

kam

01-14-2003, 03:52 AM

I currently have him running a Novak Dually....I took out the Super Rooster that was in it so that he wouldnt get used to having reverse.
We actually went to the track tonight to see if we could break my "custom" chassis brace. Well it looks like I'm going to hold off on ordering a replacement. The one that I made looks to be bulletproof. It's an aerospace plastic that I brought home from work that's light and can take temps above 180C.

drumr racer

01-14-2003, 10:14 PM

Do you think you could fabricate that part 4 me?

FullTilt

01-25-2003, 09:34 PM

hey guys,

What wheels do you guys use on your trucks? The stock ones that come with the xxt truck look kinda dull and I was wondering if any of you upgraded to chrome or know of any that would work with the xxt?

Thanks!

drumr racer

01-26-2003, 01:15 AM

Hey, do you guys think they (as in Team Losi) will make a XXX'CR, or a XXX'tcr?

RallyRoach

01-26-2003, 11:41 AM

I don't think so. If I'm remembering corectly, there was a XX Kinwald buggy, but no 'Name Brand" XXT. Besides, the XXX series has had quite a long shelf life now, and it is still essentially unchanged. I think if Losi decides to revamp the XXX in any signifigant way, they will take the oportunity to sell a whole new vehicle and the XXXX will be born.

Just my $0.02...

RallyRoach

FullTilt

01-29-2003, 10:08 PM

Does anyone know if there are aftermarket shocks(complete with springs, oil resevoirs, shock shaft, etc.) that would fit a XXT? I am looking for something that is extremely durable but won't cost me a bundle.

drumr racer

01-29-2003, 10:45 PM

Full Tilt: if you can spend alot of money, which I already know that you want to be cheap, buy some threaded shock bodies for the Evader (I'm not sure about this, but alot of people said that the threded shock bodies on the Evader will fit the XX-tcr. I'm saving money for some) They're aluminum, and really durable.
Or if you want ti spend as little money as possible, which I observed you do, live your regular shocks to their fullest, and clean them whenever you run in dusty conditions, or clean them regularly.

FullTilt

01-30-2003, 12:56 AM

drumr-- thanks... I was just browsing online for some ideas and came across the duratrax ones you mentioned. They're not that steep in price ($15.99 at Tower) so I might go for those unless there's a better option out there (plus I need to make sure they will work because under Tower's description, it says it only works for something else). My regular shocks are broken so there's no point in cleaning it any more. :(

Do you know if lunsford titanium turnbuckles will fit the stock rod ends for the XXT? My stock turnbuckles are warped beyond repair and I really don't want more stock items that don't last.

drumr racer

01-30-2003, 07:51 PM

All that I know is that I could'nt find Lunsford for My car, so I bought Factory Team Titanium turnbuckles made for the XXT (or XX-TCR) at my LCS. If you can find them, I've just got them awhile ago, and they hold up great.
they look blue

drumr racer

02-06-2003, 07:11 PM

Hey! where is everyone. Say hello.

Toiffel

02-11-2003, 10:01 AM

tHIS MIGHT BE STUPID QUESTION, BUT ANYWAY... I HAVE LUNSFORD TITANIUM TURNBUCKLES, AND THE RPM SHORT BALL LINKS, I WENT FOR A SHORTER FRONT CAMBER LINK, FROM 2 B TO 3 B, OR SOMETHING LIKE THAT, BUT THE MANUAL SAYS I SHOULD HAVE A 1/2 DEGREE NEGATIVE CAMBER, AND WITH THIS CHANGE, I HAVE MORE LIKE A POSITVIE CAMBER, AND A CAN'T ADJUST ANYMORE TO GET THE RIGHT CAMBER BECAUSE THE LUNSFORD TURNBUCKLES ARE A LITTLE LONGER THAN THE STOCK MATT FRANCIS ONES THAT I HAVE, WILL THIS AFFECT MY TRUCKS HANDELING IN A NEGATIVE WAY?? OR THIS IS WHAT HAPPENS NORMALLY WHEN YOU GO FOR SHORTER CAMBER LINKS?? OR IS IT BECAUSE OF THE SLIGHTLY LONGER TURNBUCKLES?? OR EVEN BETTER SHOULD I NOT WORRY ABOUT IT?? THANKS........

BobT

02-11-2003, 08:22 PM

Originally posted by Toiffel
tHIS MIGHT BE STUPID QUESTION, BUT ANYWAY... I HAVE LUNSFORD TITANIUM TURNBUCKLES, AND THE RPM SHORT BALL LINKS, I WENT FOR A SHORTER FRONT CAMBER LINK, FROM 2 B TO 3 B, OR SOMETHING LIKE THAT, BUT THE MANUAL SAYS I SHOULD HAVE A 1/2 DEGREE NEGATIVE CAMBER, AND WITH THIS CHANGE, I HAVE MORE LIKE A POSITVIE CAMBER, AND A CAN'T ADJUST ANYMORE TO GET THE RIGHT CAMBER BECAUSE THE LUNSFORD TURNBUCKLES ARE A LITTLE LONGER THAN THE STOCK MATT FRANCIS ONES THAT I HAVE, WILL THIS AFFECT MY TRUCKS HANDELING IN A NEGATIVE WAY?? OR THIS IS WHAT HAPPENS NORMALLY WHEN YOU GO FOR SHORTER CAMBER LINKS?? OR IS IT BECAUSE OF THE SLIGHTLY LONGER TURNBUCKLES?? OR EVEN BETTER SHOULD I NOT WORRY ABOUT IT?? THANKS........

To answer your question; positive camber will make your truck handle differently than negative camber. I don't believe you will like the difference.

Now let's clarify something. You replaced your Matt Francis XXXT camber links which are titanium with another set of Lunsford turnbuckles. Is that correct?

If you replace all the links with a set of Lunsfords you may have the front, rear and or steering links interchanged.

The rear links are longer than the front. If you are putting a XXXT set on an XXT you have two choices. See if your LHS will exchange them for a set for a XXT or go one step farther in the upgrade. Replace the ball cups with Traxxas captured ball ends. These ballends are shorter but stronger. We do this on our XXXNT's to strengthen them. Put a washer on the 4-40 screw before putting it through the ball and you will never loose that link in a bad landing or accident.

I've snapped the titanium link but the Traxxas captured ball ends were still in place. :cool:

Toiffel

02-12-2003, 01:51 PM

I broke two of the stock ones, so I changed them all, and yes you are right, I had the camber links and the tie rods interchanged, hanks for your help!!!

madmudder

02-12-2003, 06:25 PM

Hi I want to know what parts I would need to make a xx into a xxt. Thanks.

RallyRoach

02-12-2003, 09:30 PM

It might be easier to just find a rral xxt, but if you're bound and determined, you'll need the main chassis, the front and rear arms, anything that looks like a turnbuckle, shocks, shock towers, wheels and tires, body mounts and atruck body. Hope that helps :)

RallyRoach

BobT

02-13-2003, 10:26 AM

Originally posted by madmudder
Hi I want to know what parts I would need to make a xx into a xxt. Thanks.

There are less than a dozen parts that are the same for both the xx and xxt. Chassis, transmission, a-arms, camber-links, hubs and hub carriers are all different. It would be cheaper to buy a new XXXT Spec and upgrade with bearings than to try to convert your xx to a truck. A used Matt Francis edition or standard XXXT should also be cheaper.

Sell the xx and put the money towards a newer truck. You'll be dollars ahead.:cool:

mx416

02-17-2003, 10:14 AM

madmudder - you will also need a new transmission because they have different ratios.
Buggy - 2.19:1
Truck - 2.61:1

drumr racer

02-24-2003, 10:03 PM

I just ajusted my ride heigth correctly today. Boy is it hard to get it right without threadead shocks.
I have those... collar things

BobT

02-25-2003, 10:43 AM

Originally posted by drumr racer
I just ajusted my ride heigth correctly today. Boy is it hard to get it right without threadead shocks.
I have those... collar things

Yes but but in most cases once they are set you never need to worry about them again. And you've saved $40 by not investing in the threaded shocks. I have them on my XXXT and they were nice for setting the ride hight two years ago.

If I had it to do over I would have spent the $40 on new tires.:p

drumr racer

02-25-2003, 10:38 PM

Ya, but I'm gonna try 2 get threaded shocks for my new B4, when I get it.

I'm gonna run that thing like no other, even more than my XXTCR:p So I'll have to rebuild the shocks alot like my RC10T2

drumr racer

02-25-2003, 10:41 PM

Originally posted by BobT
If I had it to do over I would have spent the $40 on new tires.:p
or a new graphite chassis brace, and a front bulkhead

this is my hundredth post, I'm happy

drumr racer

03-03-2003, 08:17 PM

I just found a Aluminum rear bulkhead that somebodies selling!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

drumr racer

03-07-2003, 06:14 PM

some body bought it off eBay for 30 dollars

RCMark

03-09-2003, 05:50 PM

I have a XXT-CR chassis I'd like to sell. Stock, have 2 bodies. Posted under the Buy/Sell/Trade section but thought someone here would be interested. Open to reasonable offers.

Thanks.

holshotracer

03-10-2003, 05:26 PM

our family owns three xxts. my dad have a xxt and i have a xxt graphife plus and a custom oval xxt with front shocks on all four corners. we run stock motors in them.

RallyRoach

04-16-2003, 04:07 PM

So, with winter finally gasping its last breath, does anybody have any interesting plans for their XXT?

I'm going to be getting a much faster motor for mine, because we have 2 more offroad tracks opening up, both of them VERY large. The 17x2 just won't do this year :)

Plus, we may have a large dirt oval opening. It will be used mainly for nitro stadium racing, but if there's interest there may be an electric class.

Anyway, start charging packs by's, the good weather's a-comin'!

:D

RallyRoach

bashbrook

04-20-2003, 11:00 AM

I bought my truck about 2 1/2 months ago and about 6 weeks ago I started having trouble with my differential. I run 1 or 2 batteries and the differentials comes loose, it so loose that the gears spin the truck does not move. HELP!

holshotracer

04-21-2003, 03:38 PM

check to see if you are putting it in right, on mine the diff screw head is on the left when looking at the back. also check it before you run so it isn't loose to begin with.

drumr racer

04-23-2003, 12:00 AM

I finally got a B4, but that doesn't mean that I won't stop searching on Ebay for eye candy on my TCR

holshotracer

04-25-2003, 07:24 PM

i was jumping my truck last night and took out a least two bearing in the hubs not bad considered how hard it was landing.

offroader

06-02-2003, 09:10 AM

Hey guys, I'm just about to pick up a used XX-T and was wondering what bodies fit this truck? Will most of the stadium truck bodies from HPI fit properly?

Thanks

holshotracer

06-02-2003, 01:20 PM

the way that the body mounts are you might the bodies that i use are losi or dahms. you may have to make new body mounts or raise the stock ones.

GT Freak

08-17-2003, 09:36 PM

I just got my XXT, came with aluminum bulkhead,no body, foams, decent batteries, pink springs all around! nice ride, it was my online dads, who died last weds!:(

GT Freak

08-18-2003, 10:34 AM

Does anyone know where i can get a gear cover for my XXT at??? mine didnt come with one and i want to run this in the dirt!

RallyRoach

08-18-2003, 12:00 PM

IMHO, you shouldn't run a gear cover with these trucks. The covers are imperfect at best on keeping dirt out, and if any gets in, its like a meat grinder after the run. I race on mostly sandy tracks, and have had few problems not running the ocver. If a rock does get stuck, a quick throttle blip clears the spur and your fine.

That being said, you can still get the covers from Losi, and I think RPM may still make theirs. Try your LHS for these parts :)

RallyRoach

GT Freak

08-19-2003, 12:53 AM

WOW!! took the truck out for the first time today! its quicker than any of my other rides. Im loving this. Wonder if i should run it offroad or not now... :confused: :D

GT Freak

08-19-2003, 12:16 PM

Found out today that i have a aluminum rear bulkhead. is that a good upgrade or not?? also, the slipper on my jrxt buggy is the same as on my XXT! talk about coolness:cool:

Pete Vitale

08-19-2003, 08:58 PM

I'm picking up a XX-T for thirty bucks. I run a XXX-T MF normally, but I figure thirty bucks, why not. I dumped my XX buggy when I found parts were starting to get hard to find at the track. This thing is complete but the body is beat down. Is it hard to get a body for these? Worse come to worse can I get an evader body to fit? Thanks for any input.

GT Freak

08-20-2003, 03:10 AM

well, now im wondering what body will fit a XXT... :confused:

RallyRoach

08-20-2003, 11:56 AM

You can find the stock Losi XXT bodies on eBay every once in a while, but as for new bodies that fit, Dahm's has a bunch that will work (Plus Sheldon's Hobbies has them on sale right now :D )

Other than that, T3 bodies can be made to fit, it just requires some holes to be cut in the hood to allow the shock towers to clear. Gives it kind of a Hot-Rodish look, but not the best for protection of parts.

RallyRoach

GT Freak

08-20-2003, 06:05 PM

please post a link to sheldons hobbies!

RallyRoach

08-21-2003, 11:53 AM

Dude, not to be a complete jerk or anything, but have you never heard of Google? I just searched Sheldon's Hobbies and surprise, it popped right up.

RallyRoach

GT Freak

08-25-2003, 12:36 PM

:D Found quite a few bodies there for my truck.. now which to choose,which to get:confused:

GT Freak

08-26-2003, 09:15 PM

doesnt ANY ! have 1 of these awsome trucks :confused:sheesh, thought more would b enjoying these!

GT Freak

08-27-2003, 10:26 AM

well, i found a temp solution for my truck: IF u lose your front end brace use a peice of lexan. i did andits held up fine so far! :cool:

also, if its big enough, u can put a stickie on it :D

likeitloud2

09-06-2003, 11:01 PM

I have been using the Proline GMC truck body (for XXX-T). The fit is good and holds up well to the bashing!

GT Freak

09-10-2003, 12:05 AM

might have to try that body out! got a link to it :confused:

GT Freak

09-12-2003, 01:20 AM

found a crowd pleaser body for the xxt will fit a xx-t just right :)

GT Freak

09-13-2003, 12:26 AM

well, just picked up a XXTCRGP today,came with wore out foams,no body,and needs some work, but it will get done soon, in other news the CROWD PLEEZER body for the XXXT fits the XXT perfectly :cool: so i know what body i can use for my other truck now!:D

streetracer

09-18-2003, 07:07 PM

I have had my xx-t g+ for about six months or so. it is awsome. i totally restored it from the ground up. still needs a body a blue aluminum motor mount.\
TIP= dont use the stock aluminum screws in places that are most intense, like under the chassis. as they looki good, they break real easily, and will make you have to tear the chassis apart to get them.

does anybody have a fairly decent motor mount , blue proferd, that they will sell, or trade?

lmk

Streetweapon1@hotmail.com

GT Freak

09-19-2003, 02:35 AM

i have a G+ that im restoring too, Im needing the wheels,kit tires,and body to complete it. wonder if losi STILLhas those items in stock :confused:

gattm99

09-19-2003, 11:09 AM

I've got an XX-T for sale on ebay,

http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=3145958170&ssPageName=ADME:L: (http://)

GT Freak

09-19-2003, 07:24 PM

that link doesnt work.... :rolleyes:

GT Freak

09-22-2003, 04:27 PM

wish more people typed about this awsome truck! im working on my XXTg+ gotta find a different body for it then the crowd pleaser im running on the other one so there different looking! anyone got any suggestions :confused:

SnakeEyesRacing

10-12-2003, 01:18 AM

Getting a parts truck off e-bay to put back in service. It used to be a daily driver.

GT Freak

10-14-2003, 02:21 PM

if i had a cc, then id use ebay, but since i dont... oh well :rolleyes:

SnakeEyesRacing

10-22-2003, 08:14 PM

Its free if you dont sell anything
No cc needed

hondaguy812

11-15-2003, 06:20 PM

I have a XXT that I just raced for my first time last week. I had some questions tho. All the other cars could blow me in a drag. The only reason I did so well racing it was because of my driving skills. I am confused why my car is slower. I have a brand new green machine 3 motor in it and a trinity 2500 Mah battery pack. My gearing is 86 spur 19 pinion. My esc is also pretty new but it was very cheap....a duratrax auto-sport ESC. Anyone got any suggestions?? Other then the speed this losi kicks ass. I love it

GT Freak

11-22-2003, 11:53 PM

if the XXT= the evader...... shouldnt it be now called XXE??

anywhoooo, i have 2 XXT's, one is reg, the other is CRGP since the reg will be used for bashing, what offroad wheels and tires are right for that idea??

foam tires tip1: when running in the street, and u need to clean the foams, run through the grass! works for me! :D

tr918

12-16-2003, 12:39 AM

For bashing any tire will do. I prefer the losi "smasher " truck tires front and rear. They do really well in grass and pavement. Perfect for curb hopping. :D Any similiar tire will do though. It is all preference.

The losi part number is A-7680R Front/Rear “Smasher” All Terrain Tires (Red) w/Foam $17.95

GT Freak

12-27-2003, 10:24 AM

well, im buyint a gtx/nxt. so when i got it, i just took the wheels of it and put them on my XXT also, just picked up a XXT body :eek: talk abot cool! now my xxt is almost finished! if i could just find the origanal wheels/tires/hubcaps........

tr918

01-05-2004, 12:54 AM

GT Freak

Go to Losi's web site and get the part number for the dished wheels with the disc caps. Stormer hobbies carries them. I do not remember the part number. If you have the Losi Part number your LHS should be able to order them for you.

GT Freak

01-10-2004, 08:38 AM

called sheldons, no luck so now im stumpted... where to go what to do.... :confused:

tr918

01-23-2004, 04:25 AM

just trying to see if I could still post to this thread!

Snake Charmer

01-28-2004, 11:40 PM

I got my parts truck runing two weeks ago. It has all new electornics, including a G7, xxtra, and hellfire motor. :cool:

Snake Charmer

01-28-2004, 11:50 PM

pic.
By the way A.K.A. Snake Eyes Racing was my handle

Snake Charmer

02-19-2004, 07:35 PM

I may be slow but, I just find that many of the parts for a duratrax evader ST will fit a XXT cr. They share suspension angle to the "T" Cool more parts sorces.:cool: :D

Snake Charmer

02-22-2004, 01:47 AM

I got 2nd in inter. stock truck last night.:D I'm working on a XXT non cr to run as a mod truck.:cool:

SniperBait

05-03-2004, 03:46 PM

I just found an old XXT in my mom's basement and i was wondering if anyone knows where I could get the instruction sheets for it, I looked on teh Losi web site, but all they had was an exploded view with a parts list... any help you guys could give would be great! Thanks

SB

tr918

05-05-2004, 04:41 AM

Sniper Bait - Congrats on the found item. Losi unfortunately does not have an electronic version of the XXT manual. Try ebay, someone may be selling an old XXT manual. If you still have trouble finding one let me know. I may be able to scan mine and email an electronic version of it to you.

Have you been able to determine which XXT it is? XXT or XXTCR. If it is the XXT, then my manual should work. If it is the XXTCR then it will help but not much.

The XXT has a shorter chassis and velcro battery straps. The transmissions are the same. The XXTCR has the longer chassis, came in a regular and a graphite version, and had a battery holder similiar to the current XXXTs. The front ends are identical but there are some slight differences in rear suspension geometry.

Hope this helps. Good luck.

-TR

SniperBait

05-12-2004, 06:58 PM

tr918: it's the original XX-T and the only part of the instructions I need is for the diff. I dont want to install the thrust bearings in the wrong order/backwards. After lookng on ebay, I found nothing useful, just a couple rolling chassis... so if you are willing to scan those pages for me I would be most gratefull! :D :D PM me for my email.. thanks again

Also, if anyone has any tips on tuning the diff they would be helpful as well...

SB

tr918

05-13-2004, 06:06 AM

SniperBait - I will PM you when I get it scanned in. (sorry, having scanner issues) The diff is not hard to tune. Very easy compared to the xxxnt. I am fairly sure there is a section in the manual on how to tune the diff. If there is, I will scan that also.

I think you and I are the only ones left who read this forum! :D

SniperBait

05-14-2004, 02:27 PM

It does seem kinda quiet in here... It makes me wonder, if no one needs info on these trucks any more, how many are sitting collecting dust? seems a shame really...

SB

GT Freak

05-20-2004, 01:45 AM

iI have 2 of these awsome truck, ones a reg, the other is a graphite version, wonde should i keep them or get rid of them :confused:

tr918

05-20-2004, 05:33 AM

GTFreak - Whether you keep them or not is up to you. If you have other vehicles and the xxt's are collecting dust, you might want to think about downsizing. My xxt was my first hobby grade RC. So I keep mine around for sentimental reasons. I bought it when the xxt kit was first released (Bushings kit w/ no electronics). If you do decide to keep one of them and sell the other you might get more cash for the graphite version.

Did you ever find the xxt wheels and disc caps you were looking for?

-TR

GT Freak

05-20-2004, 01:13 PM

nope ,nothing yet on the wheels/caps! :(

shadmaster4

05-24-2004, 02:35 PM

sup homie g's...here is my XXT...

GT Freak

05-25-2004, 12:49 AM

nice ride. just got my XXT running today. Just gotta paint up the stock kit body for it now! :Dwhat is the pink motor i c there :confused:

GT Freak

05-25-2004, 09:25 PM

just got done runnig.. with a 1700 batt, spec motor, and 81/21 gearing, i got 45 min of run time :eek: Hows that for fun??

The Modfather

06-20-2004, 02:17 PM

I ended up with an XXT in a trade I did a while ago - the car is just a roller, missing all electrics. I have everything installed except the servo - it's a little strange, and I"m not exactly sure how it mounts in there -

Can someone provide me with a blow up diagram, digital pic, or some other form of help here?

Thanks!

tr918

06-21-2004, 04:03 AM

Mod - I got your pm. I will email the manual shortly. When tearing apart the front end be sure to inspect the bulkhead thouroghly. Pay particular attention to the plastic ringed areas where the pins join the bulkhead to the chassis. This is the weak point of the bulkhead and normally where it breaks. Check to see if the rings are cracked or show signs of bending (indicated by white areas). If it is replace it. I have broken the bulk head a couple of times. Don't worry though, mine only broke b/c I ran it into a car tire the first time and a mailbox the second time(Street racing :D ).

Check out Losi's website they have a nice exploded view of your truck.
http://www.teamlosi.com/exploded/index_old.htm

The manual I have is for a xxt kit w/ bushings. It will work for all xxt kits except the xxtCR and xxtCR graphite edition. They have a different length chassis and slipper configuration.

Hope this helps
-TR

The Modfather

06-21-2004, 10:24 AM

tr918 - A MILLION thanks to you!

I have received your email, and will make it publicly available to anyone else that wants it. I'd like to build a repository of manuals that so people can find anything they need on one site, but I'm not sure of the legal ramifications :(

Anyhow, as far as teh front bulkhead is concerned - 3 of the rings on teh left side are "expanded" or opened up - but not broken off. I'll run with it like this for the time being - hell, worst case is that it breaks when someone else is driving it :)

tr918

06-22-2004, 04:10 AM

Modfather- RPM makes a very nice cushioned bumper/skid plate for the xxt. When you do finally replace the front bulkhead you might want to look into getting one. It takes some of the stress off of the bulkhead during a front end collision.

-TR

The Modfather

06-23-2004, 12:37 AM

tr918

06-23-2004, 04:40 AM

Mod- Here is the link for the RPM bumper. http://www.rpmrcproducts.com/products/losi/chassis.htm

My LHS had it for $3.75. I know it isn't a high end mod but IMO it is worth the 4 bucks. The bumper does not look like much, but it works.

-TR

The Modfather

06-23-2004, 10:38 PM

GT Freak

06-24-2004, 01:22 AM

well, still wanting to get rid of my XXT, anyone want it :confused:

tr918

06-25-2004, 02:30 AM

GT- Every addict on this site is looking for a vehicle. As always though it depends on vehicle and price. If you are actively trying to sell one of the trucks then put it on ebay or post it in the buy/sell forum in the zone. I have a tendency to low ball people on price. I would tell you what I think you might get for the regular or graphite version, but I don't want to insult you. Remember these trucks handle great but they are out dated. There is not much demand for them other than parts trucks or those of us who like the trucks and are not concerned with having a state of the art racer. If you are serious, post it on the buy/sell forum. If you price it reasonable enough, someone will buy it.

Snake Charmer

06-28-2004, 04:49 AM

I finily got all my passwords in order. now I can bring you pics. of my XXT I've been wining with. :cool: I updated my web site and now have a set-up for my local truck for this truck.

Snake Charmer

06-28-2004, 04:53 AM

[IMG]here it is.

Snake Charmer

06-30-2004, 01:55 AM

[IMG]one more pic.

tr918

06-30-2004, 02:16 AM

Snake Charmer - Very nice truck. Glad to see someone racing and winning with an old favorite.

GT Freak

06-30-2004, 02:47 AM

hhmmm, think ill just hang on to my XXT and see what i can do with it...

Question time:

what rims (off road) can i use??
what tires would be good for bashing around, that give long life??

Snake Charmer

06-30-2004, 02:52 AM

Any rims that fit XXT or XXXT will do just fine. Pro-line Dirt-Hawgs are good for plaing aroud.

tr918

06-30-2004, 05:47 AM

If you like the mt look the proline masher 2000's are a good time. Any xxt, xxxt, xxxtmf2 or xxxnt wheel will fit the xxt. This gives you the option to choose from all brands and styles of tires and wheels made for the xxxt and xxxnt.

Snake Charmer

07-05-2004, 07:47 PM

what's up with your truck?

tr918

07-08-2004, 09:50 AM

nope ,nothing yet on the wheels/caps! :(

GT - I was looking for replacement wheels and caps for my xxt and found the following. http://www.teamlosi.com/partlist/parts/offroad-whls.htm

It appears that Losi changed the part numbers for the wheels. Horizon Hobby has them. Here is the link for the Front and Back wheels

Front: http://horizon.hobbyshopnow.com/services/advanceresultsDetail.asp?display=pictures&strProd=&strSearchType=ALL&strInCategory=CPT&strInManufacturer=LOS&PageNum=2&strSortBy=ProdNumAsc
Part numbers: LOSA7074(YELLOW) AND LOSA7080(WHITE)

Rear: http://horizon.hobbyshopnow.com/services/advanceresultsDetail.asp?display=pictures&strProd=&strSearchType=ALL&strInCategory=CPT&strInManufacturer=LOS&PageNum=3&strSortBy=ProdNumAsc
Part numbers: LOSA7124(WHITE) AND LOSA7125(YELLOW)

Spare discs(Hub caps) are LOSA7198

Hope this helps

-TR

GT Freak

07-08-2004, 03:34 PM

those rears r 4 the buggy i believe(but could b wrong)wonder if the yellow drake wheels will fit my truck??

tr918

07-09-2004, 05:39 AM

those rears r 4 the buggy i believe(but could b wrong)wonder if the yellow drake wheels will fit my truck??

I am not sure about the rear wheels? :confused: The drake wheels will fit your xxt. I swap wheels off of my xxxnt drake all the time. Any xxxt or xxxnt wheel will fit the xxt. And likewise any xxt wheel will fit the xxxt and xxxnt.

Snake Charmer

07-10-2004, 03:52 PM

there all the same.

GT Freak

07-12-2004, 01:52 AM

gave my friend the XXT, so now he can run trucks AND tc's with me.... :D

tr918

07-13-2004, 04:54 AM

GT - That was very generous of you. It is refreshing to hear that there are still people like that around! :cool:

GT Freak

07-14-2004, 04:03 PM

im going to be running ( hopefully this yr) on the track we made about 5 yrs a go which is still there.

surface is: clay but has a light coat of loose sitting on top... what would be my choices for tires :confused:

tr918

07-15-2004, 06:14 AM

I have not raced my xxt in a long time. I used to run on moslty loose dirt tracks and used losi step pins. From what I have heard though the Pro line bow ties work well on the blue groove which is similar to the track you are describing. Losi has a tire selection guide on their web site. Losi tire guide (http://www.teamlosi.com/newprod/tirechart/tirechart.htm)

That might help. If not check in the xxxt threads and ask those guys.

jrc3

09-10-2004, 07:19 PM

tr918

09-29-2004, 06:49 AM

i have a brushless e-maxx and have an oppertunity to get an xxt. i want to throw a hacker c40 6t and car sport controller at it or buy a novak ss5800 system. what would i have to do to make the tranny stand up to BL. the xxt already has mip cvd's. i know nothing about the xxt.

thanks a bunch, jack

Jack, All you need to do is change the spur gear and the pinion gear to the right gearing for the BL. The stock xxt tranny is tough enough to handle the brushless as long as you do not run more than 8 cells on it. Any more than that or if you have incorrect gearing on your spur and pinion you could melt the plastic gears. I do not know of anyone who makes aftermarket metal tranny gears for the xxt. Good luck and I hope this helps.
-TR

microrcdude

09-29-2004, 10:13 PM

im thinking of buying a XXT for a friend of mine. Are they still good trucks?

tr918

09-30-2004, 06:55 AM

im thinking of buying a XXT for a friend of mine. Are they still good trucks?

Yes, they are great trucks. The newer xxxt and xxxt2 trucks have some greater suspension tuning abilities and a different gear ratio. Aside from that they are similiar trucks. If you can get a deal on the xxt buy it. If not you can usually get a xxxt off of ebay for about the same or slightly more.
Good luck.

-TR

microrcdude

09-30-2004, 06:37 PM

ok cool. He had a XXT when he had to get out of the hobby due to some other reasons, but hes racing for me in january, and i thaught id surprise him a little.

hbash

10-03-2004, 08:25 PM

ive got a quick question. xxt what are the most cmmom screw sizes. because im going to buy some good hex drivers but dont want a bunch of them that dont even fit thanks.

tr918

10-04-2004, 06:59 AM

ive got a quick question. xxt what are the most cmmom screw sizes. because im going to buy some good hex drivers but dont want a bunch of them that dont even fit thanks.

I can not remember all of them off hand. The ones off of the top of my head are the smaller hex wrenches like a 3/32 and a 5/64. I use those two very often on both my xxt and my xxxnt. You can pick up a standard allen wrench set at the hardware store for under 10 bucks. Hope this helps.
-TR

SuzookKING

12-22-2004, 04:11 PM

http://www.teamdmg.com/images/cowbug.jpg
http://www.teamdmg.com/images/cowtruck.jpg

tr918

01-05-2005, 07:33 AM

SuzookKING --Nice ride! What bug body did you use?

microrcdude

01-05-2005, 07:16 PM

I want to say HPI, but i dont think it has that rear end on it.

tnjoker

07-17-2005, 08:23 PM

New to RC here. I have both an Evader Pro and a Losi XXT. I believe that everything from the rear shock tower forward is interchangeable on both trucks. Hope this helps the people looking for parts. Towerhobbies.com has a wide selection of replacement parts for the Evader. I know I can't find many suppliers for xxt parts so this helps me a lot.

tr918

07-18-2005, 07:51 AM

Welcome, I have heard a lot of people say that the two are interchangeable. I have never tried. I have been lucky and can still get parts at my local hobby shop. He has the ability to order the parts directly from Losi's distributor.(I think its Horizon Hobbies). I have had my xxt since it first came out. I don't race it anymore, I just keep it for sentimental reasons. It is more of a backyard toy and a training tool to teach the 5 year old how to drive.

alabamarcguy

08-10-2005, 09:37 AM

Well Thats Great They Interchange I Have 2 Xxts Love Em

alabamarcguy

09-13-2005, 08:55 AM

i recently got a xxt from a friend it ha ben built fromt he ground up never ran last night i installed electrics on it and whn i punched it it made an awful sound like stripping of gears i took th tranny apart no teeth were chewed up sometimes it runs fine but i suspect somethin in the bottom end is not right could the diff gear be out of round? any info would be appreciated

alabamarcguy

09-14-2005, 03:24 PM

anyone here?

Kden46

10-02-2005, 12:01 AM

Man I'm glad I found this thread! I was just given a XXT from my wife's cousin. It was in pretty bad shape but the drivetrain is pretty good!

I'm looking into the conversion from the hydra drive to a dual pad slipper setup as I've heard it's easier to maintain and get parts for?

I've read a little through this thread about the use of Evader ST parts on the XXT. I can tell you from my experience that parts are very similar like arms, shock towers. But some parts require some minor modification to fit right. I needed to replace the front bulkhead on my XXT and was able to get a Evader ST for some parts. The bulkhead from the EST is near exact to the XXT piece except the way it mounts to the chassis. The XXT bulkhead uses 5 hinges I think and the EST only uses 3. All I had to do was cut the chassis to fit the EST bulkhead and it works fine!

The EST suspension arms seem to use a slightly smaller hinge pin than the XXT does.

I'm fixing up the XXT to go racing soon! I've been racing my 18T and have gotten the bug to race another class! I have'nt race 1/10th off road since the Heavy Metal class a long time ago!!!! :eek: :D

Rtsbasic

10-10-2005, 05:26 AM

Hey, I just brought another car (RC10T2) which has a Team Losi slipper clutch setup fitted, as near as I can tell its the same used on the XX-T (has a big thing that goes infront of the spur and a slipper pad behind it). No idea how it was fit on there, but its not using a standard top shaft so thats probably Losi as well.

So my question to you guys, is what does it do? Is this the hydra drive thing? Should I keep it or put a normal setup back on? I can't for the life of me figure out what the big black thing infront of the spur does, all I can see is it has what looks like a big gear in from the parts diagram.

Cheers.

TraxxasJessica

11-28-2005, 01:19 AM

SnakeCharmer is me. And mine is still going. How about some parts Losi. ;)

bakabaka

11-28-2005, 03:24 AM

Hi!

Just curious, I have an XX-T in runnable condition kicking around that I'm not using. The electronics were all moved to other vehicles except for the motor, but everything worked fine when last it was used. About how much do they go for these days? I may end up posting it to the "for sale" section, if it's still worth something.

Have fun! :)

TraxxasJessica

11-28-2005, 09:32 PM

Heres (http://cgi.ebay.com/TEAM-LOSI-XXT-XX-T-CR-RTR-GRAPHITE-) one on ebay.

bakabaka

11-29-2005, 02:26 AM

Hi TraxxasJessica,

Thanks! I should have thought to look at ebay.

Have fun! :)

losifreak2004

11-29-2005, 05:25 PM

GT freak - I'd try Losi IFMAR Pins on that style track. Those have been my favorite tire the last several years of racing.

B3racer - The Hydra Drive has a fan inside of it that turns through thick silicone fluid (the viscosity of the fluid changes how the Hydra Drive works) and helps provide stability (through somewhat of a flywheel effect) on slippery and rough tracks..in the mid 90's, the Hydra Drive rocked on anything but the most blue-groove race tracks.

I'm not sure who all is still reading this thread. If anyone has any questions I'll do my best to chip in some help.

Aaron Waldron
Team Losi Factory Driver

GT Freak

12-05-2005, 01:38 PM

what wheels fit the XXT?? mine only has foams on it right now!! :o heres a pic of it

TraxxasJessica

12-06-2005, 11:05 PM

Cerent Losi rims and Duratrax with some work.

XXT gets 8th place A-main at SoCal Supercross. :D

GT Freak

12-07-2005, 07:52 AM

GJ for the XXT, as for thse rims, would hpi stars work?? or do i need something else??

TraxxasJessica

12-09-2005, 02:57 AM

They may fit. I belive they come with adapters for Losi.

bakabaka

12-09-2005, 03:02 AM

They may fit. I belive they come with adapters for Losi.

They do, I used a set on both an XX-T and an Evader ST for a while.

Have fun! :)

philp37

12-16-2005, 06:26 PM

Any one know of an internet retailer that sells losi and has nice break downs with pictures of each and every part like tower has?

bakabaka

12-17-2005, 04:35 AM

Any one know of an internet retailer that sells losi and has nice break downs with pictures of each and every part like tower has?

Hi philip37!

Not to state the obvious, but Horizon Hobby has a somewhat similar setup. At least, they definitely do for the Mini-T (the reason I go to the site.)

http://www.horizonhobby.com

Have fun! :)

TraxxasJessica

12-19-2005, 04:33 PM

:( I had to decomission my XXT cr. She now hangs in my garage. :(

All due to lack of parts. Thanks Horizon :mad:

philp37

12-19-2005, 05:42 PM

That sucks!! It is bad for both Losi owners and the respect for and value of the truck in general. Drops my opinion of Losi value alot. Definately weighs heavy in my choosing of a new monster truck that I am taking much time to decide on. No question, if parts support ceases that quickly for a product that was so popular as the xxt.... Losi is out for me.

bakabaka

12-20-2005, 04:01 AM

That's pretty much why I'm selling mine, while it's still in good running condition. I had 3 XX-T chassis (two in running condition, one for parts) at one time, but they seemed to break a bit more than I liked. Keep in mind that as many have mentioned, the Duratrax Evader ST has parts that are very similar to those on the XX-T. You might want to check to see if the parts you've broken can be replaced with Evader ST parts. I'm not sure about the XX-T CR model though.

Have fun! :)

philp37

12-20-2005, 05:23 AM

What about these guys?

http://www.losipartshouse.com/servlet/StoreFront

bakabaka

12-20-2005, 06:04 PM

What about these guys?

http://www.losipartshouse.com/servlet/StoreFront

That looks like a good source. One has to wonder how much longer they'll be able to keep themselves in XX-T parts though, esp. if they're no longer being manufactured. One of the LHS around here had the occasional part for it kicking around, but the owner just retired and the shop's closing (maybe already closed.)

Have fun! :)

TraxxasJessica

12-23-2005, 12:07 AM

No mater what, trans. cases are just not to be had any more, I've looked.

philp37

12-23-2005, 12:30 AM

Did anyone try contacting Losi on this issue?

GT Freak

12-23-2005, 10:36 AM

jessica, im more then willing to let my XXT go, just let me know! :) all im wanting for it is another truck, since my friend wants one.

bakabaka

12-23-2005, 12:05 PM

Same here, although I don't need another RC car/truck (my wife would kill me...) It's a bit far though, since I'm in North California (your website states SoCal).

Have fun! :)

philp37

12-26-2005, 03:15 AM

Any one know if MF2 arms fit evader?
I know that MF1 or XXXT arms do, as to the xxt cr arms.
I think that the same answer for the question: do mf2 arms fit on the xxxt? will also suffice.

TraxxasJessica

12-30-2005, 06:02 PM

Tie rods and axles will have to be chaged as will.

ClodzillaIIIMan

01-01-2006, 12:05 PM

Hey guys if anyone needs a XXT complete tranny or suspension arms or wheels and tires i may be able to sell all them if anyone is interested??

LMK! my email is ultimatercforum@yahoo.com

GT Freak

01-25-2006, 01:21 PM

does anyone know what rims will fit my XXT :confused: right now it has foams on it!

philp37

01-30-2006, 02:51 AM

does anyone know what rims will fit my XXT :confused: right now it has foams on it!

Any rims listed for xxt, xxxt or Duratrax evader will fit your xxt. Associated rims will go on but they have the wrong dish and will ruin handling.

Sause

06-08-2006, 11:35 PM

Just dusted off my xxt-cr and man its still rocks.

I do have an issue with the turnbuckles. I need so titaniums. I think that the xxt's would work but am not sure. am I right?

philp37

06-09-2006, 06:41 AM

I could be wrong, but for the cr, I think you need the xxxt turnbuckles. The cr had the longer a-arms of the xxxt before the xxxt came out with that and a number of other changes.

CeeKay

04-14-2009, 08:05 PM

Does anyone have a parts pull-out or manual?

Here's my XX-T, awaiting parts (in the mail) for a diff rebuild...

http://c3.ac-images.myspacecdn.com/images02/71/l_a69916e208ae4ef585d520fc5d58cb12.jpg

http://c2.ac-images.myspacecdn.com/images02/100/l_9599e67655c0473abf052af5c545e0d9.jpg

And, the XX-T with the Micro riding piggy-back! :)

http://c2.ac-images.myspacecdn.com/images02/85/l_010b126d7a764e2eafd4581053dc371d.jpg

:)

XX-T paintjob: Old old green paint from last decade, sharpie, Competition Orange (toxic crap paint/mask job on purpose), and grey primer. X)

Electronics and stuff:

Bearings throughout, a slough of wheels (Mashers x4, bowties x2, Losi super-rib things x2, Losi standards x2, Pro-Line sand paws x2. Futaba Magnum Sport Tx/Rx, LRP F1 Pro fwd/rev ESC, Speed Gems 2 9t Single powerplant, Lunsford blue titanium turnbuckles with steel Losi XXX-T buckles in the back because I misplaced one back 6-9 years ago, 2" red springs in the front, 2.5" pink in the back.

Bought it on eBay around 2001-2003 abouts, then broke it that year, at which time I retired it and fell out of the RC hobby for a while. Had an itch to get back into it, and I've been scratching for weeks now, but my XXT is just such a basket case that I'm slowly turning it into a truck built entirely on replacement parts. X)

When I got it, it was green with silver tape along the bottom for an accent...

Anyway, enough rant...

- CK